How to switch from keys to door codes: a step-by-step plan

Replacing keys with codes is not about buying a lock. It is a small project that involves doors, internet, bookings and people. Below is the order that lets you do it without closing the property and without a nervous first week.

In short The switch from keys to door codes takes seven steps: count the doors, check what lock sits in them, get Wi-Fi to the gateways, decide where bookings come from, fit and test the locks, set up the guest message, and keep the keys as a backup for the first weeks. Lock delivery usually takes 5 to 10 working days, and fitting goes room by room, so the property keeps taking guests the whole time.

Step 1. Count the doors and split them into two groups

Start with a sheet of paper, not a catalogue. Walk the guest's route from the street to the bed and write down every door that is locked along the way.

  • The guest's private doors: rooms, apartments, cabins. Each one needs a lock with a keypad. These are the doors the software fee is counted from.
  • Shared entrances: the gate, the driveway, the main door, the staircase. One device per entrance is enough here, often a reader with an electric strike rather than a lock. In PinRoom they are free of charge.

Add the doors a guest should never open: the linen store, the utility room, the private part of the house. They stay on an ordinary key or get a lock with a code for staff only.

Step 2. Check what is in the door

The type of door decides whether the lock simply screws on or you need a joiner. Measure one thing: the distance from the centre of the handle to the centre of the cylinder. That is the lock spacing.

What you haveWhat fitsHow much work
A door with a cylinder mortise lock, 72 mm spacing3060TTL-72old plates off, new lock screwed on
A door you must not alterC1 electronic cylinderonly the cylinder is swapped, no drilling
A door that opens to the outside6100TTL or 2022TTL-L, both IP55depends on the door
New doors or a refurbishmentSS-08 with its own mortise lockordered together with the doors
A gate, driveway or staircase doorSKD 11 reader and an electric strikeneeds a 12 V supply at the entrance

If you are not sure, photograph the edge of the door with the lock visible, and the handle from both sides. BH WANDEX uses such photos to pick the model before quoting. All the models are shown in the lock catalogue.

Step 3. Get internet to where the gateways will stand

A battery lock has no internet of its own. A code entered in the panel reaches it through a Wi-Fi gateway placed within Bluetooth range of the lock. With no gateway you would have to set each code from a phone while standing at the door, which defeats the purpose.

  1. Mark on a floor plan where the sockets near the doors are. The gateway runs on mains power.
  2. Check with your phone that there is Wi-Fi in those spots. The manuals of G2 gateways require a 2.4 GHz network.
  3. Count gateways with a margin. BH WANDEX states that one serves up to 6 locks, but thick walls and ceilings shorten the range. The final number is set from the floor plan and confirmed during fitting.

What happens when the network goes down is covered in a separate guide: smart lock battery dead or no internet. The short version: guests whose code is already set walk in as normal.

Step 4. Decide where bookings will come from

The code should appear by itself, so the software has to know who is arriving and when. List the channels your guests book through and match a route to each.

  • WuBook or Zak: PinRoom reads bookings directly, changes and cancellations included. See PinRoom and WuBook.
  • Booking.com with no channel manager: a connection through Beds24, with guest details.
  • Airbnb and other portals: an iCal calendar link, checked every 15 minutes. You add the guest's contact by hand.
  • Phone bookings and regulars: a booking entered in the panel.
  • A system with its own TTLock connection: some booking systems, Beds24 among them, talk to TTLock locks themselves. In that case codes are configured there.

Step 5. Fit the locks and test every door

Fitting does not interrupt the running of the property. The fitter takes the rooms that are free on the day, and the rest carry on with the old keys. The 3060TTL can also be fitted by yourself and, according to BH WANDEX, that does not void the warranty.

Once the lock is on the door comes the part you must not skip:

  1. Add the lock to the TTLock app and name it after the room, for example "Room 4".
  2. Assign the lock to a gateway and check that the gateway sees it with the door closed.
  3. Set a test code remotely and open the door with it. Only this proves the whole chain: internet, gateway, lock.
  4. Open the door with the mechanical key and write down where that key is kept.
  5. Delete the test code and make sure it no longer works.

During PinRoom onboarding we run this test with you on every door and assign the locks to rooms in the panel.

Step 6. Set up the message the guest will receive

Even a perfect lock does not help if the guest cannot tell which door is theirs. The message with the code should answer three questions: where to enter, what to type and who to call.

  • When: in PinRoom you choose to send right after booking, the day before arrival or on the day of arrival at a set hour. The default is the day before at 10:00.
  • How: by email and SMS. Portals do not always pass on a phone number, so two channels at once are safer.
  • In which language: messages are ready in 8 languages, including English, German and Ukrainian.
  • What to add yourself: a description of the way in ("the gate on Forest Street, second door on the left"), check-in hours, the Wi-Fi password and a phone number in case of trouble.

Send the first message to yourself and walk the route as if you were there for the first time. Wherever you hesitate, a guest will too. A ready example is in the guide door code message template.

Step 7. The first weeks: keys stay as a backup

Do not take the key rack down on day one. Run both ways side by side for two or three weeks.

  • Guests who booked before the change should get a message with the code and a short note that there is no key to collect any more.
  • Give staff and cleaners manual codes from the panel in place of keys. Each person should have their own, so the opening history shows who came in.
  • Write down in one place what to do when a battery is flat: where the mechanical key is, where the power bank is, and who has the TTLock app with admin rights.
  • Enter a phone number and an email for alerts in the settings. PinRoom warns you there when a code was not created or a lock lost its connection.

Five mistakes that spoil the start

  • The gateway is too far from the door. It works on fitting day and stops once the fire door is shut. Always test with doors closed.
  • One permanent code for everyone. That is a lockbox in a new form: every past guest knows it. A code should be separate for each booking and expire after departure.
  • Locks on the rooms only. A guest with a room code is left standing at a locked gate. Plan the shared entrance together with the rooms.
  • No emergency number in the message. A guest who does not know who to call will call the booking portal.
  • Throwing the mechanical keys away. You need them rarely, but when you do, you need them at once.

Facts about locks, gateways and fitting: wandex.pl, hotel code locks and questions and answers about electronic locks (both in Polish), read on 13 November 2026. Lock supply and fitting by BH WANDEX covers properties in Poland.

What the software costs per lock is on the pricing page. If you would rather have someone go through these steps with you, write to us through the form and say how many doors you have and which booking system you use.

Questions about moving from keys to codes

How long does the switch from keys to codes take?

Lock delivery usually takes 5 to 10 working days. Fitting in a property with 20 rooms usually takes 2 to 3 working days. Add two or three weeks during which the keys are still at hand as a backup.

Does the property have to close during fitting?

No. Locks go on room by room, in the rooms that are free that day. The remaining rooms take guests the way they always have.

Can I start with just a few rooms?

Yes, as long as you solve the shared entrance straight away. A guest with a room code still has to get through the gate and the main door. More locks can be added later with no change of software.

What about guests who already have a booking with key collection?

They get a code like new guests do, provided their booking is in the system the software reads stays from. It is worth adding one sentence to the message saying that keys no longer need to be collected.

Do I still need keys after the change?

Only emergency ones. The code locks in the BH WANDEX catalogue can be opened with a mechanical key in case of a flat battery or damage. Keep the keys in one place that your staff know.

See the panel on a demo property

The demo opens without login and nothing you do there is saved or sent. The panel is in Polish for now.